jtrcnc's blog

xAluminium sliding windows are a popular choice for quick and effective ventilation and simple functionality.

 

What you’ll need to get started

Before you begin, make sure you’re wearing the right safety gear for the site you are working on, and the tools you are using.

 

There are many reasons a product may need adjusting:

 

The house may have settled over time.

The original installation may have been slightly out.

All of our operable windows have built-in adjustment allowance to accommodate this.

 

The tools you will need are:

A drill with Phillips head bit.

Phillips head screw driver.

Side cutters.

A rubber mallet.

A second pair of hands (depending on the size and weight of the product).

 

 

Before the adjustment.

To begin, visually inspect the product from the inside of the house, looking at the gaps between the sash and the frame at the bottom and on the sides. If the sash looks crooked in the opening, take note of which side needs to be raised or lowered to square it back up.

 

 

 

Adjusting your A&L Boutique Awning Window.

Remove the sash, firstly making sure that the security block in the head of the frame is out of the way.

 

 

 

Hold the sash on both sides and lift it up into the head. At the same time, pull the bottom of the sash towards you until the whole sash can be removed. Turn the sash upside down so that the plastic guides are facing up.

 

 

 

There are three points on the guides to allow adjustment, a low, centre and high point.

 

 

 

Using the side cutters, carefully remove the sash guide by levering it off the rail. You may need to use a flat head screw driver to lift the guide enough to fit the side cutters in.

 

 

 

Rotate the sash guide into the new desired position and put it back into place on the sash.

 

 

 

Finishing your adjustment.

Turn the sash back up the right way and lift it back up into the head of the frame before lowering it down onto the track again.

 

 

 

Slide the sash back towards the closed position and re-inspect the gap between the sash and the frame. Repeat the process until you are happy with the operation.

Aluminum foil is made from an aluminum alloy which contains between 92 and 99 percent aluminum. Usually between 0.00017 and 0.0059 inches thick, foil is produced in many widths and strengths for literally hundreds of applications. It is used to manufacture thermal insulation for the construction industry, fin stock for air conditioners, electrical coils for transformers, capacitors for radios and televisions, insulation for storage tanks, decorative products, and containers and packaging. The popularity of aluminum foil for so many applications is due to several major advantages, one of the foremost being that the raw materials necessary for its manufacture are plentiful. Aluminum foil is inexpensive, durable, non-toxic, and greaseproof. In addition, it resists chemical attack and provides excellent electrical and non-magnetic shielding.

 

Shipments (in 1991) of aluminum foil totaled 913 million pounds, with packaging representing seventy-five percent of the aluminum foil market. Aluminum foil's popularity as a packaging material is due to its excellent impermeability to water vapor and gases. It also extends shelf life, uses less storage space, and generates less waste than many other packaging materials. The preference for aluminum in flexible packaging has consequently become a global phenomenon. In Japan, aluminum foil is used as the barrier component in flexible cans. In Europe, aluminum flexible packaging dominates the market for pharmaceutical blister packages and candy wrappers. The aseptic drink box, which uses a thin layer of aluminum foil as a barrier against oxygen, light, and odor, is also quite popular around the world.

 

Aluminum is the most recently discovered of the metals that modern industry utilizes in large amounts. Known as "alumina," aluminum compounds were used to prepare medicines in ancient Egypt and to set cloth dyes during the Middle Ages. By the early eighteenth century, scientists suspected that these compounds contained a metal, and, in 1807, the English chemist Sir Humphry Davy attempted to isolate it. Although his efforts failed, Davy confirmed that alumina had a metallic base, which he initially called "alumium." Davy later changed this to "aluminum," and, while scientists in many countries spell the term "aluminium," most Americans use Davy's revised spelling. In 1825, a Danish chemist named Hans Christian Ørsted successfully isolated aluminum, and, twenty years later, a German physicist named Friedrich Wohler was able to create larger particles of the metal; however, Wohler's particles were still only the size of pinheads. In 1854 Henri Sainte-Claire Deville, a French scientist, refined Wohler's method enough to create aluminum lumps as large as marbles. Deville's process provided a foundation for the modern aluminum industry, and the first aluminum bars made were displayed in 1855 at the Paris Exposition.

 

At this point the high cost of isolating the newly discovered metal limited its industrial uses. However, in 1866 two scientists working separately in the United States and France concurrently developed what became known as the Hall-Héroult method of separating alumina from oxygen by applying an electrical current. While both Charles Hall and Paul-Louis-Toussaint Héroult patented their discoveries, in America and France respectively, Hall was the first to recognize the financial potential of his purification process. In 1888

 

The Bayer process of refining bauxite consists of four steps: digestion, clarification, precipitation, and calcination. The result is a fine white powder of aluminum oxide.

The Bayer process of refining bauxite consists of four steps: digestion, clarification, precipitation, and calcination. The result is a fine white powder of aluminum oxide.

he and several partners founded the Pittsburgh Reduction Company, which produced the first aluminum ingots that year. Using hydroelectricity to power a large new conversion plant near Niagara Falls and supplying the burgeoning industrial demand for aluminum, Hall's company—renamed the Aluminum Company of America (Alcoa) in 1907—thrived. Héroult later established the Aluminium-Industrie-Aktien-Gesellschaft in Switzerland. Encouraged by the increasing demand for aluminum during World Wars I and II, most other industrialized nations began to produce their own aluminum. In 1903, France became the first country to produce foil from purified aluminum. The United States followed suit a decade later, its first use of the new product being leg bands to identify racing pigeons. Aluminum foil was soon used for containers and packaging, and World War II accelerated this trend, establishing aluminum foil as a major packaging material. Until World War II, Alcoa remained the sole American manufacturer of purified aluminum, but today there are seven major producers of aluminum foil located in the United States.

Aluminum manufactures aluminum cast plates that have ultra-high-performance alloys optimized for plastic mold tooling plate. Ellwood Aluminum specifically engineers to maximize the operational advantages of using aluminum alloys for today’s molding technologies, including injection molding, RIM, structural foam molding, vacuum forming, blow molding, rubber molding, tire molding, composite tooling and molds, as well as thermoforming molds.

 

The high-quality alloys of our aluminum cast plate allow the product to be used for aerospace composite tooling, robotic, and machinery components. Our aluminum cast plates are forged and heat treated to offer mold builders a higher strength and higher hardness in a larger aluminum mold plate thickness range.

Aluminum Cast Plate Advantages

 

Equiaxed grain structure

Low residual stress

Extreme flatness tolerance capability

Good internal soundness

Excellent surface finish

Many choose aluminum cast plate because it is faster and less costly to fabricate than steel. In addition, aluminum is easier to handle and stock since it weighs significantly less. The thermal conductivity of aluminum plate is higher than steel, so aluminum can cut molding cycle times to help you increase your output. Aluminum casting plates also allow the molds to cool more evenly, minimizing risk of distortion in the molded part.

 

Aluminum Cast Plate Manufacturing Applications

 

Foam molding

Vacuum forming

Blow molding

RIM and structural foam molding

Rubber molding

Tire molding

Injection molding

Thermoforming molds

Composite tooling and molds

Aerospace composite tooling, robotic and machinery components

Aluminum cast plate is used in a variety of industries in the end applications of products that are used every day, including automotive, medical, aerospace, electronics, and consumer goods.  Some of these everyday products include plastic trays, food containers, medical devices, vehicle doors and panels, refrigerator linings, machine housings, and enclosures.

 

 

In simple words, air conditioner aluminum foil means the aluminum foil for air conditioners which is used to improve its cooling effect. The first air conditioner aluminum foil was introduced in 1980 and at that time it was 0.15mm to 0.2mm thick but these days it is only 0.09 to 0.15mm. Different kind of aluminum foils is developed to give different kind of effects. There are many types like anti-corrosion air conditioning aluminum foil, hydrophilic air conditioning aluminum foil, self-lubrication air conditioning aluminum foil, etc.

 

Why you should Choose Air Conditioning Aluminum Foil?

If you are curious to know why you should choose an aluminum foil then there are a lot of reasons behind it. Aluminum foils provide a lot of benefits. Some of them are:

 

They are beneficial because of their characteristics like good thermal conductivity.

They provide Easy processing of deformation.

Also the price of aluminum foils are very low in comparison to others.

It is very easy to recycle aluminum foils.

Its less shipping cost makes it a great choice for manufacturers.

They are very easy to maintain.

It has so many benefits and because of that, aluminum foil has become the first choice for air-condition heat exchange material.

 

How to Choose a Quality Aluminum Foil in China?

Now you have all the information and you almost know everything about the benefits of choosing an aluminum foil. All the information is mentioned above but one more thing that you have to make sure that you are choosing a quality aluminum foil. There are so many options available in the market and it is really difficult to choose an authentic one. This is the most important thing you need to take care of while choosing an aluminum foil. The quality of the aluminum foil depends on their manufacturers. No matter how much research you do, if you are choosing your aluminum foil from a wrong manufacturer then you won’t get great quality.

As the key part of the complete flake ice machine, the ice flaker evaporator plays important role in making ice. To matching the various Ice flaker evaporator, you can make different choice about the refrigeration units in different refrigerant (R22, R404A or R717) by yourselves.

 

flake-ice-machine

 

characteristics:

 

The ice flaker evaporator processed from special alloy with lightness and high heat conduction efficient approximating that of Aluminum.

 

Every flake ice scraper processed in special designing without any jointing then in high solidity, and can rotate well nearly 8 years.

 

All components selected is of top-quality and meet configuration need, which makes the evaporator hold the less space, and achieve best performance.

 

The flake ice is glittering and translucent, hard and pure.

 

Ice making and dropping in high speed.

Flake Ice Machine

If you need soft, moldable ice, a flake ice machine is the best option for your business. While flake ice is commonly used in food displays, it has other uses as well. Businesses use flake ice for serving shellfish, for treating injuries, and, of course, to cool beverages.

 

Here are some of the ways a flake ice maker can benefit your business.

 

What is Flake Ice?

Flake ice is a soft, moldable form of ice similar to crushed ice. However, flake ice has more of a snow-like texture than crushed ice, which makes it easier to work with when creating food displays. Crushed ice is made by crushing fully formed cubes. What results is a handful of crushed bits from a hard, solid cube. Flake ice, on the other hand, has a light, airy feel that allows it to mold together to form shapes easily.

 

Flake ice is used in several applications. Here are the most popular…

 

Flake Ice Machines for Food Displays

Flake ice was designed with food displays in mind. That includes seafood and produce displays, where food needs to stay on ice to keep fresh. Flake ice is also great for beverage displays or drink tubs, where customers can grab their drinks. Flake ice holds bottles and cans in place and provides even cooling throughout.

 

Flake ice machines produce ice that is light and airy, so ice sticks to itself. The texture of the ice allows you to create mounds of ice to present food or drinks any way you’d like. Flake ice enables business owners to get creative with their products. Show food or drinks off in dazzling displays that entice customers, but feel safe knowing they will stay fresh on display.

 

If you run a fish market, a large industrial flake ice machine is the most cost-effective way to supply fishmongers with ice. These industrial ice makers can produce hundreds of pounds of flake ice to display to potential customers.

 

Top Quality Flake Ice Machines

Flake ice machines are available in our all-inclusive ice machine program! Get maintenance, cleaning, and repirs for a low, month;y cost!

Flake Ice Makers for Hospitals and Physical Therapy

Along with nugget ice, flake ice is popular in hospital ice makers and ice chip makers. Doctors and physical therapists use it to treat sprains and other injuries.

 

Since flake ice is soft and malleable, it provides a more even cooling surface than other types of ice cubes. Since the ice is able to make more contact with the injured area, it provides maximum heat transfer. The ice pulls heat from the injured area faster and more evenly.

 

Flake ice is also softer than traditional ice cubes, so they are easier on plastic bags. Over time, ice cubes melt and become more jagged, increases the chance that the bag will rip open leaking water over the patient. Since flake ice is so soft, it won’t cut through cold compresses. Patients can heal and stay dry in the process!

 

Flake Ice Machines for Bars and Restaurants

Flake ice makers are used in restaurants and bars to produce ice for drinks and other uses.

 

Flake ice is an excellent addition to specialty drinks. Classic cocktails like mai tais and margaritas are best served over crushed ice, but that often requires a blender. With flake ice, bar staff can grab ice and toss it into any cocktail without using a blender.

 

Blended drinks, like daiquiris, are a notorious hassle for bar staff because they take time to make and the process pulls them away from other customers. Furthermore, traditional ice cubes are rough on blenders and can break them over time. Flake ice makes blending fast and easy, so your staff can quickly serve drinks to customers and save money buying multiple blenders.

 

Flake ice machines are also beneficial for oyster bars. Traditionally, oysters are served on a bed of cold rock salt to keep them in place on a plate. Many oyster bars have switched to using flake ice because it keeps oysters at a safe serving temperature and still keeps them locked in place.

 

Where Can I Get a Flake Ice Machines?

Many manufacturers make flake ice makers. ICENICE flake ice machine models are one of the best ice machines in the industry. These machines come in all sizes, from 50 lbs to over 1000 lbs of ice a day. If you are in need of ice block machine, you can also consult with them to know things you want.

Recently, the demand of ice blocks machine is very large. To reduce costs, some customers buy brine type ice block machine.  And more conviently,  such as automatic model, the CBFI brand direct cooling block ice machine is the better choose for you!

 

However, When using the ice block machine, it is necessary to understand some operation knowledge. For example, the point that needs to be paid attention to is the heat dissipation problem. Because some heat will be generated during the manufacture of the ice block, it needs to be dissipated. Otherwise, the location will put a burden on the equipment and will also affect the power of the ice blocks. Therefore, we must pay attention to certain details. Specifically, the matters needing attention in the use of the CBFI ice block machine also include the following aspects.

 

      1、pay attention to placing in a suitable environment

 

Before these applications, the ice blocks machine should be installed in a clean, clean and well-ventilated environment indoors. It cannot be placed in the open air to prevent it from being exposed to wind, rain and sun, otherwise it is very risky and simple aging. In addition, the ice block machine manufacturer must lay it on the ground so that it can run smoothly during the operation to prevent noise or risk. At the same time, it should be noted that there must be a certain space around to allow more Good heat dissipation.

 

news-CBFI-img

 

         2、pay attention to be satisfied with its operating conditions

 

The ice block machine should be supplied with its regular independent power supply and the method of ensuring that the power supply is grounded. This is a basic requirement to ensure the normal operation of the machine, and it must be equipped with fuses and leakage maintenance switches together with voltage fluctuations. Can not exceed the scale of the rule in order to ensure the safety of the application. The water source used by an ice block machine should meet the drinking water specifications, and it can only be officially used after being filtered.

 

         3、Pay attention to the regular cleaning work

 

 In order to ensure the normal operation of the ice block machine, the water valve filter should be cleaned every two months to prevent clogging, and although the ice block machine will drain the water in the sink to reach the cleaning after each use However, it is not enough to do so. It is necessary to perform thorough cleaning and disinfection at least once every six months. If it is not used for a long time, it should be cleaned before it can be reused. Moreover, the ice block machine manufacturer also reminds to keep the interior dry after washing, and can use a hair dryer to dry it.

 

The above are the aspects included in the attention of the operation of the ice block machine. In addition, it must be very shockproof during transportation. If it is a long-distance transportation, you can put some foam in it and fix it on the car to prevent it from shaking. The direct cooling type ice blocks machine manufacturer introduced that after the transportation is completed, it should be noted that it cannot be used immediately, and it should be allowed to stand on a flat ground.

 

About Ice blocks machine manufacturer, you could choose ICENICE China Top Ice Machines Manufacturer. Daily Capacity: 1-100 Tons. It is widely used in docks, ice-making plants for food processing and preservation, aquatic product preservation, cooling, ice sculpture shaping, edible ice manufacturing. You might also want to know things aboutice conveyorits needed during the ice producing.

Ice Conveyor is a multi-component, glycol-based anti-icing agent that will keep your production lines moving like no other product on the market. Designed for the most extreme conditions, it has a longer-lasting affect and works at a colder temperature than any other product. It keeps coal and other material moving, even when facing:

 

Extremely wet coal

Extreme cold (down to -70º F!)

Extreme precipitation

Extreme angle of belts

Extremely old, hardened or weathered belts

Other approaches to managing cold temperatures and harsh precipitation stop working or begin to lose effectiveness as soon as temps drop to between 0º and -10º F – making them barely suitable for a mild winter in the north!

 

In addition, temps that fall below 20º F result in belt hardening, which only worsens the colder it gets. Hardening causes material to backslide – creating more delays. Unlike other options, Ice Free Conveyor actually creates belt friction, allowing your products to continue moving UP the belt instead of down.

 

Ice Free Conveyor also prevents or minimizes fines carry-back and build-up on belts, idlers and pulleys that can clog systems, causing belts to tear and motors to overheat. This not only prevents delays but also saves you costly repairs and maintenance.

 

Ice Free Conveyor can be applied to tops and bottoms of conveyor belts as well as to trough idlers and tail pulleys. When applied prior to shutdown it prevents ice glazing and ice and snow buildup. If applied at start-up or during operation, it speeds the removal of ice and prevents further buildup.

 

And it does all of this while using less product than other options: because it only requires an application rate of one gallon per minute per single complete revolution, there are less over-sprays and puddles of wasted product.

3d printing vs cnc

3D printing is a rapidly growing technology with many advantages over traditional manufacturing methods. It however has its problems, including that 3D printing cannot be effectively used for mass production, and is limited in speed and accessibility. Another manufacturing technique for low-to-mid production is CNC machining (computer numerical control), a fairly common subtractive technique for part creation. We decided to compare the advantages and disadvantages for each method to establish where these technologies are most appropriate.

 

Subtractive vs Additive Manufacturing

They key difference between 3D printing and CNC machining is that 3D printing is a form of additive manufacturing, whilst CNC machining is subtractive. This means CNC machining starts with a block of material (called a blank), and cuts away material to create the finished part. To do this, cutters and spinning tools are used to shape the piece. Some advantages of CNC machining include great dimensional accuracy as well as many compatible materials, including wood, metals and, plastics.

 

3d printing vs CNC

 

3D printing, or additive manufacturing, involves parts being created layer-by-layer using materials such as plastic filaments (FDM), resins (SLA/DLP), plastic or metal powders (SLS/DMLS/SLM). Using a source of energy such as a laser or heated extruder, layers of these materials are solidified to form the finished part. Advantages of 3D printing include its freedom of shape, applications in many sectors, accuracy, speed, and ability to cut costs and weight in parts.

 

 

There are however several machines that have sought to combine these two forms of manufacturing in one. Most notably of these, the ZMorph 2.0 SX, is marketed as a CNC mill which also functions as a 3D printer. This includes a CNC mill with 3 axes as well as a print head due to its interchangeable heads. Moreover, several companies have recently closed successful Kickstarter campaigns with these combined machines, such as Mooz’s 3-in-1 3D printer.

 

3d printing vs cnc

The ZMorph SX 2.0 includes interchangeable CNC and 3D printing heads.

 

3D Printing vs CNC Machining: Materials

Both 3D printing and CNC machining are compatible with a wide variety of materials, including both plastics and metals. 3D printing however is more focused on plastics overall, though this is changing rapidly as better and more affordable ways of 3D printing metal are being developed by manufacturers such as 3D Systems, Arcam, Desktop Metal and Markforged.

 

The most commonly used plastics used in CNC include ABS, Nylon (PA66), Polycarbonate (PC), Acrylic (PMMA), Polypropylene (PP), POM and PEEK. A very commonly used metal in CNC machining is aluminium, used by prototyping companies to create high-quality prototypes in a variety of industries. Aluminium is recyclable, has good protective qualities, and can create effective prototypes for machining. Other commonly used metals include stainless steel, magnesium alloy, zinc alloy titanium, and brass.

 

3d printing vs cnc

Aluminium is a commonly used metal with CNC due to its good mechanical properties.

 

In 3D printing, commonly used thermoplastics include ABS, PLA, Nylon, ULTEM, but also photo-polymers such as wax, calcinable or biocompatible resins. Some niche 3D printers also allow for the printing of parts in sand, ceramics, and even living materials. The most common metals used in 3D printing include aluminium, stainless steel, titanium, and inconel. It is also worth noting that to 3D print metal, expensive ($100,000+) industrial machines are required. Some materials such as superalloys or TPU (flexible material) cannot be created with CNC, so must be used with 3D printing or rapid tooling technology.

CNC machining service come in different shapes and forms. This article explains the difference between CNC machining and CNC turning, two common CNC technologies.

 

CNC machining is a rapid manufacturing process that turns digital 3D designs into plastic or metal parts by selectively cutting away material. Many companies require CNC machining service to make parts and prototypes, and many industries use the versatile technology.

 

But CNC machining comes in various forms. Although all CNC machining technologies follow a similar workflow — software turns the digital design into machine instructions, which instruct the CNC machine to cut material — the hardware for cutting material can differ greatly between machines.

 

This article discusses the main differences between two of those machines: CNC mills and CNC turning (or lathes centers).

 

In the article we discuss the essential features of CNC milling and CNC turning while also presenting the main advantages of each technology and a selection of common parts that companies can manufacture using each process.

 

What is CNC Milling?

cnc milling machine

CNC milling is one of the most common CNC machining service, and machinists can use it to make a wide variety of CNC machined parts. Prototype companies often use CNC mills to make one-off functional prototypes.

 

CNC mills use computer instructions to move a rapidly rotating cutting tool along three or more axes. When the spinning cutting tool makes contact with the workpiece, it removes material in a controlled manner. The cutting tool makes a succession of passes against the surface of the workpiece until the workpiece resembles the desired part.

 

Most CNC mills keep the workpiece stationary, holding it down on the machine bed with a vice. However, multi-axis CNC mills may rock or rotate the workpiece to create a greater number of cutting angles. This allows the machinist to create more complex parts without having to manually reorient the workpiece.

 

Providers of rapid prototyping services use CNC milling because it is a one-stop, end-to-end process with short lead times.

 

What is CNC Turning?

cnc turning machine

CNC turning is a form of CNC machining that machinists use to make rounded, cylindrical, and conical parts. Although it is less versatile than CNC milling, it is one of the most popular CNC machining services and rapid prototyping services.

 

Machines that carry out CNC turning are called CNC lathes or CNC turning centers. They are different from CNC mills in that they rapidly rotate the workpiece in a chuck but do not rotate the cutting tool. The cutting tool, affixed to a turret, moves towards the spinning workpiece under computer instructions and removes material where necessary.

 

A CNC lathe can cut the outside of the workpiece or bore through the inside to create tubular CNC machined parts.

 

The turret of the machine may have multiple cutting tools that can be individually engaged as required.

 

Advantages of CNC Milling

 

CNC mills offer numerous advantages to manufacturers and prototype companies. Unlike lathes, mills are versatile machines capable of creating a range of different shapes. Furthermore, a variety of cutting tools can be used to serve different operations such as roughing and end-milling.

 

Although they are manufacturing machines in their own right, mills are also useful for post-machining. For example, they can be used to add details to turned, molded, or 3D printed parts.

 

CNC milling is also fast, repeatable, and inexpensive in low volumes — partly because it does not require tooling. It is therefore found among manufacturing services and rapid prototyping services.

 

Advantages of CNC Turning

 

The biggest advantage of CNC turning is its ability to create round profiles. It is much more difficult to achieve perfect roundness using other CNC machining services like CNC milling or CNC routing.

 

CNC turning is also highly accurate, which makes it a valuable technology for boring holes of precise dimensions with set tolerances.

 

CNC milling and CNC turning can be combined to reap the benefits of both processes. In most cases, CNC turning takes place first, allowing the machinist to mill further (asymmetrical) details on the part.

 

Parts made with CNC Milling

 

Example parts made with CNC milling include:

 

Fittings: Milled fittings connect two or more parts together

Enclosures and housings: Electrical devices and other products can use custom-milled enclosures to protect internal components

Brackets: Milled brackets can contain custom threads and holes and may be more complex than sheet metal brackets

Gears: CNC milling can produce straight and spiral gears for mechanical devices

Mold tooling: Milled tooling, made of steel or aluminum, allows for rapid prototyping of molded parts

Engine parts: Automotive engineers use CNC milling for engine blocks and other parts

Medical devices: CNC mills can produce implants, surgical instruments, and other medical devices

Water pumps: Multi-axis mills can create reliable impellers for hydraulic equipment

Forming punches: CNC mills can create other manufacturing equipment, such as forming punches for sheet metal fabrication

Parts made with CNC Milling

Parts made with CNC Turning

 

Example parts made with CNC turning include:

 

Rollers: CNC lathes can fabricate rollers with tight tolerances for industrial use

Ball joints: CNC turning is ideal for rounded connective devices like ball joints

Nuts and bolts: The accuracy of turning makes it suitable for tolerance-critical items like nuts and bolts

Shafts: Shafts with rounded profiles are highly suited to CNC turning

Flanges: CNC turned flanges can strengthen beams and pipes

Nozzles: Nozzles are typically cylindrical or conical with hollow insides, making them suitable for CNC turning

Turbines: CNC turning can produce round turbine blades for the energy industry

Firearms: A CNC lathe can produce the tubular shape required for a firearm barrel

Parts made with CNC Milling

Which should you choose?

 

As a rule of thumb, CNC turning is best for parts with round, cylindrical, or conical profiles, and CNC milling is best for everything else. If in doubt, a machining expert can guide you to the right CNC machining service for your unique project.

 

That being said, CNC milling and CNC turning can be combined to good effect. If a part has a predominantly round shape but also requires asymmetrical cuts or features, CNC milling can follow CNC turning in sequence. And although it is less common, CNC turning can also follow CNC milling — if a boxy or irregular-shaped part requires a large hole bored through its center, for example.

 

Finally, sometimes you don’t have to choose: CNC milling-turning centers integrate both technologies into a single production device.

Pages: «« « ... 5 6 7 8 9 »